What size label fits 100 cc to 400 cc supplement and vitamin bottles?

What are the standard label sizes for cc packer bottles, tubs and droppers?

When you request a quote for custom printed supplement labels, always write dimensions as Width × Height (W × H in inches). Width is the horizontal wrap distance around the circumference of the bottle, and Height is the vertical measurement from bottom to top along the straight wall. Because two 150 cc bottles from different plastic or glass molders can have slightly different neck finishes (such as 38-400 vs 45-400) and shoulder slopes, use the chart below as your starting benchmark, then verify the straight vertical panel height on a physical sample from your co-packer before locking in your dieline.

How do I measure the straight wall and neck-band clearance on a cc bottle?

Every HDPE, PET and amber glass packer bottle has three distinct zones: a rounded bottom heel (where the mold seam curves inward), a straight vertical cylinder wall in the middle, and a rounded top shoulder leading up to the threaded neck. Pressure-sensitive labels only lie flat on the straight middle cylinder. If your label height extends even 1/16 inch onto the curved shoulder, the top edge will form vertical darts or air tunnels as the bottle spins through the applicator. On dietary supplement bottles, you also need to account for the clear perforated PVC heat-shrink band that your co-packer shrinks over the cap and neck for tamper evidence. When that shrink band extends too low down the shoulder, it can overlap the top edge of a tall paper or film label and pull it upward during heat shrinking. Stopping your label height a full ⅛ inch below the top shoulder break gives the shrink band clean glass or plastic to grip.

1. Place a flat ruler vertically against the side of the bottle and measure only the flat middle band where the ruler touches completely.
2. Subtract ¼ inch from that straight-wall height (⅛ inch clearance above the bottom heel and ⅛ inch below the top shoulder break).
3. Wrap a flexible tailor's tape around the middle of the bottle to read the exact circumference in inches (or multiply diameter by 3.1416).
4. Subtract 3/16 to ¼ inch from the circumference so the left and right ends of the wrap never overlap onto each other.
5. Divide the total circumference by 3 to find the width of your front Principal Display Panel (PDP).

How do I divide a wrap label into the front PDP, Supplement Facts and info panels?

Once you know your total wrap width (for example, 6.0 inches wide on a 150 cc bottle), you need to divide that horizontal width into three clean panels so shoppers can read your front branding in one glance without turning the bottle. Under 21 CFR 101.1, the Principal Display Panel (PDP) on a cylindrical container covers roughly 40% of the total circumference, though most designers keep the visual front artwork inside the center 33% to 35% of the wrap width so nothing wraps out of sight at the edges. On a 6.0 × 2.25 inch wrap for a 60-count capsule bottle, a balanced three-panel grid gives 2.0 inches in the center (or left-lead position) to your brand logo, formula name and capsule count; 2.125 inches immediately to the right for the Supplement Facts box and Other Ingredients list; and 1.875 inches on the remaining side for suggested use, caution text, manufacturer address, LOT/EXP box and barcode. If you also pack your bottle inside a retail folding carton, match those exact panel widths to your custom supplement boxes and custom vitamin boxes.

What size label fits protein powder tubs, greens canisters and pouches?

Sports nutrition powders, collagen peptides, electrolyte blends and superfood greens are typically packed in wide-mouth HDPE cylinders (measured in ounces, pounds or cubic centimeters from 625 cc to 2,500 cc) or flexible gusseted bags. On a standard 16 oz to 32 oz (1 lb to 2 lb) HDPE powder canister with a 3.75 to 4.15 inch diameter, a full-wrap roll label typically measures 11.0 × 4.5 inches or 12.5 × 5.0 inches. Because wide HDPE canisters can flex slightly when gripped or during warm filling, leaving a ¼ inch seam gap prevents buckling. Many brands also add a 2.5 inch or 3.0 inch round custom circle label on top of the screw-off lid so customers storing tubs in a deep kitchen drawer can spot the flavor from above. If you sell single-serve stick packs or 30-serving flexible bags, pair your tub wraps with matching 3.0 × 4.0 inch front and back labels on custom supplement pouches.

What when a 1 oz tincture bottle is too small for all my text?

Liquid herbal extracts, B12 drops, chlorophyll and mushroom tinctures usually come in 1 oz (30 ml) or 2 oz (60 ml) amber or cobalt glass Boston round dropper bottles. On a 1 oz dropper bottle (1.25 inch diameter, 3.93 inch circumference), your usable wrap area is only 3.75 × 1.75 inches. Fitting a front brand panel, a multi-herb Supplement Facts box, directions, warnings, a LOT/EXP stamp zone and a UPC barcode into 6.5 square inches requires disciplined layout. First, ask your regulatory advisor whether your bottle qualifies for the small-package Supplement Facts format under 21 CFR 101.36(i)(2); if it does, we size and print the layout you supply, and you can orient your barcode vertically along the seam edge. Second, pair the 3.75 × 1.75 inch primary bottle wrap with a printed outer custom tincture box that holds the full-size barcode, extended botanical story and dropper dosing chart.

1. 1 oz (30 ml) dropper bottle: 3.75 × 1.75 in wrap; leaves a 3/16 in gap on the 1.25 in diameter glass.
2. 2 oz (60 ml) dropper bottle: 4.25 × 2.0 in wrap; leaves a ¼ in gap on the 1.50 in diameter glass.
3. Never overlap laminated ends on narrow droppers: spring-back tension on a 1.25 in mandrel will lift an overlapped seam.
4. Use an outer tincture carton when your formula has a long botanical blend or multi-language directions.

What are the most common supplement bottle label sizing mistakes?

A label that is ⅛ inch too tall or wide can jam a co-packer's labeling head or wrinkle under the neck shrink band. Check these five sizing errors before you approve your proof

1. Measuring the total height of a packer bottle from base to cap instead of only the flat vertical wall between the heel and shoulder curve.
2. Running the top edge of the label right up to the shoulder break, where the co-packer's heat-shrunk PVC neck band overlaps and pulls it.
3. Designing a 100% circumference wrap with zero gap on a 1 oz dropper vial, causing the laminated trailing edge to pop up on the tight curve.
4. Making the front brand logo wider than 35% of the bottle circumference so the product name wraps out of view on retail shelves.
5. Entering Height × Width instead of Width × Height when ordering roll labels, which rotates the label 90 degrees on the applicator web.

Find your label size

Packaging for this

Custom Supplement Labels

Custom Supplement Boxes

Custom Vitamin Boxes

Custom Tincture Boxes

Custom Roll Labels

Custom Lip Balm Labels

More guides